[aprssig] FINDU RAW DATA Question

[William McKeehan]

It looks like you or your PHP page is trying to escape the quote characters ('
and "). The additional backslash characters are being passed to the G3NRW APRS
Packet Decoder which causes it to not recognize the packet.

-- 
William
KI4HDU

On Fri, May 25, 2007 11:31 am, Kai Gunter Brandt wrote:
> William McKeehan wrote:
>> I did a similar thing. It only takes one packet at a time...
>>
>> http://mckeehan.homeip.net/cgi-bin/aprs/viewpacket.pl
>>
>> But my pages recognizes the packet as follows:
>>
>> N0EOP-14>SY4Y0Q,W8GUC,KB9GYO-3,WIDE2*,qAo,KC9HAX:'pQ8l"1v/]"44}
>> APRS Data Type= Current Mic-E data
>> Radio= Kenwood TM-D700
>> Message Type= /M1/En Route
>> Lat= 39 deg 49.01 min N Long= 84 deg 53.28 min W
>> Icon= Van Overlay= (none)
>> Course= 221 deg Speed= 0 knots (0.0 mph 0.0 kph 0.0 m/s)
>> Altitude= 95 feet (29 meters)
>>
>>
>>
> yes the following packet:
> N0EOP-14>SY4Y0Q,W8GUC,KB9GYO-3,WIDE2*,qAo,KC9HAX:'pQ8l"1v/]"44}
>
> Give:
>
> N0EOP-14>SY4Y0Q,W8GUC,KB9GYO-3,WIDE2*,qAo,KC9HAX:'pQ8l"1v/]"44}
>  APRS Data Type= Current Mic-E data
>  Radio= Kenwood TM-D700
>  Message Type= /M1/En Route
>  Lat= 39 deg 49.01 min N  Long= 84 deg 53.28 min W
>  Icon= Van   Overlay= (none)
>  Course= 221 deg   Speed= 0 knots (0.0 mph  0.0 kph  0.0 m/s)
>  Altitude= 95 feet (29 meters)
>
>
> But i was using:
> N0EOP-14>SY4Y0Q,W8GUC,KB9GYO-3,WIDE2*,qAo,KC9HAX:\'pQ8l\"1v/]\"44}
>
> And this decodes as:
>
> N0EOP-14>SY4Y0Q,W8GUC,KB9GYO-3,WIDE2*,qAo,KC9HAX:\'pQ8l\"1v/]\"44}
>  APRS Data Type= (** Beacon, not APRS)
>
>
> I'm using:
> TM The G3NRW APRS Packet Decoder
> Version 2.0 (16 June 2000)
>
> So if you can decode
> N0EOP-14>SY4Y0Q,W8GUC,KB9GYO-3,WIDE2*,qAo,KC9HAX:\'pQ8l\"1v/]\"44} then
> i might be using another version of the script?
> Or i have to check that php is not parsing th / \ etc wrong
>
> LA3QMA
>
>
>
> _______________________________________________
> aprssig mailing list
> aprssig at lists.tapr.org
> https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig
>