[aprssig] Re: TNC Sleeping -- KISS OFF Utility

[Fred Atkinson, WB4AEJ]

    That's good to know.  But I know it is set to 9600 baud.  Doesn't seem
to work that way.

    Regards,



Fred, WB4AEJ

----- Original Message -----
From: "Robbie - WA9INF" <mwrobertson at comcast.net>
To: "TAPR APRS Mailing List" <aprssig at lists.tapr.org>
Sent: Tuesday, January 03, 2006 9:21 AM
Subject: Re: [aprssig] Re: TNC Sleeping -- KISS OFF Utility


> Fred,
>
> I may have missed it, but has anyone mentioned that the MFJ's has an
> "Autobaud" command. If it is on, then every time the tnc is turned off
> you must hit several characters immediately upon turning it back on to
> allow baud rate re-sync with the computer.
>
> Once that is done and working again, set AutoBaud to OFF to prevent
> having to do this again, unless the battery runs down...
>
> Robbie
>
> Fred Atkinson, WB4AEJ wrote:
>
> >     I tried that using Hyperterminal.  No reaction.
> >
> >
> >
Fred,
> > WB4AEJ
> >
> > ----- Original Message -----
> > From: <scott at opentrac.org>
> > To: "'TAPR APRS Mailing List'" <aprssig at lists.tapr.org>
> > Sent: Monday, January 02, 2006 10:56 PM
> > Subject: RE: [aprssig] Re: TNC Sleeping -- KISS OFF Utility
> >
> >
> >
> >>We're just talking about sending 3 bytes, right?  Your terminal program
> >>might let you do that (in Windows anyway) from the keyboard.  Using the
> >>numeric keypad:
> >>
> >>ALT 192, ALT 255, ALT 192
> >>
> >>Holding down ALT and typing a 3-digit number produces the ASCII
character
> >>that corresponds to that number.  Or you can just send a 3-byte file
with
> >>those bytes....
> >>
> >>Scott
> >>N1VG
> >>
> >>
> >>>-----Original Message-----
> >>>From: aprssig-bounces at lists.tapr.org
> >>>[mailto:aprssig-bounces at lists.tapr.org] On Behalf Of Mark Rennebaum
> >>>Sent: Monday, January 02, 2006 7:44 PM
> >>>To: aprssig at lists.tapr.org
> >>>Subject: [aprssig] Re: TNC Sleeping -- KISS OFF Utility
> >>>
> >>>
> >>>"Stephen H. Smith" <wa8lmf2 at aol.com> wrote:
> >>>
> >>>
> >>>>If there is a demand I could make this into a Vb program
> >>>
> >>>which I would then
> >>>
> >>>>release the source as above.
> >>>
> >>>I've done this exact program (VB 6.0) for MARCA a couple of
> >>>weeks ago, and I
> >>>can make the source (or executable) available to anyone who
> >>>wishes it. Uses
> >>>a simple GUI, can choose the port and other parameters, etc.
> >>>Pretty basic.
> >>>
> >>>Wrote a similar program for the Kantronics host mode (C0 Q
> >>>C0) as well.
> >>>
> >>>- Mark   KC7KMP
> >>>kc7kmp at hotmail.com
> >>>
> >>>
> >>>
> >>>_______________________________________________
> >>>aprssig mailing list
> >>>aprssig at lists.tapr.org
> >>>https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig
> >>>
> >>>
> >>
> >>
> >>
> >>
> >>_______________________________________________
> >>aprssig mailing list
> >>aprssig at lists.tapr.org
> >>https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig
> >
> >
> >
> > _______________________________________________
> > aprssig mailing list
> > aprssig at lists.tapr.org
> > https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig
> >
> >
>
>
>
> _______________________________________________
> aprssig mailing list
> aprssig at lists.tapr.org
> https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig