<div dir="ltr">Hi Tom,<div><br></div><div>  That's a lot of excellent work.  Curiosity: at Haystack, we often find we have to fiddle with network switch settings to handle 'jumbo frames' (MTU > 1500) right.  This comes up as you increase the sampling rate from a particular software radio and is of course totally dependent on the wire frame protocol between the SDR and driver.  Do you expect any of the Tangerine radios to produce jumbo packets, and in any case, does the RPi4 handle that case OK without dropping things?</div><div><br></div><div>  Or perhaps you never get to this use case?</div><div><br></div><div>73</div><div>Phil W1PJE</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 12, 2023 at 3:36 PM Tom McDermott via TangerineSDR <<a href="mailto:tangerinesdr@lists.tapr.org">tangerinesdr@lists.tapr.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-style:solid;border-left-color:rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div>WIth awesome support from Franco, K4VZ, there has been a lot of progress in testing</div><div>KA9Q software over a wired home network.</div><div><br></div><div>The test setup uses an RTLSDR dongle to send 192 ksps IQ data from a Raspberry Pi to</div><div>an Ubuntu 22.04 core i7 host running gnuradio with Franco's gr-rtp module. This test</div><div>setup may be one where folks have available hardware available from the junkbox and</div><div>thus able to validate their system.<br></div><div><br></div><div>The FFTW wisdom file was computed on each system before starting the tests. All</div><div>connections are using 1 GbE wired connections, no WiFi links in the system. The GbE</div><div>switch is configured with IGMP snooping turned on to avoid multicasting traffic to</div><div>unsubscribed ports. IGMP was verified as working.<br></div><div><br></div><div>Initially a RPi 3B+ with GbE interface was used. At 192 ksps It had a packet drop rate of over 10 %</div><div>resulting in unusable performance. The gnuradio flowgraph was not able to demodulate</div><div>audio from the IQ stream.  It did successfully demodulate audio when the test was run</div><div>at 48 ksps, with lower packet loss rate.<br></div><div><br></div><div>Changing to a Raspberry Pi 4 at 192 ksps improved the drop rate to 0.4%.  This allowed gnuradio</div><div>to demodulate audio, but with some artifacts.</div><div><br></div><div>Last night the fft-threads=4  line was commented out of the radiod conf file, allowing</div><div>ka9q-radio to use its default of 2 threads for the fft.  This further dropped to packet loss</div><div>rate to 0.1%.  The packet losses are now infrequent (perhaps once every 15 seconds).</div><div><br></div><div>Separately all the computers and ethernet connections have been tested with iperf3.</div><div>This is a multi-platform tool (originally Unix / Linux) that sends bursts of data between the endpoints</div><div>measuring the throughput and the TCP retry rate.</div><div><br></div><div>The Ubiquiti switch does have retries, sometimes a low number, sometimes a bit larger number.</div><div>A separate small HW switch was substituted and it has zero retries with iperf3.  All the</div><div>tests show a throughput of about 940 Mbit/s regardless, so the retry rates seem pretty small.</div><div><br></div><div>The ka9q-radio packet drop rate is the same (0.1%) using either the test with the Ubiquiti switch <br></div><div>or the small HW switch, so it doesn't seem to make much difference.</div><div><br></div><div><div>The drop rate was tested with gnuradio running, and with gnuradio not running. The latter uses</div><div>pcmcat {addr/ssrc} > /dev/null to keep the IGMP path open , and the loss rate is measured with a</div><div>tshark script provided by Franco.<br></div><div><br></div><div></div>The test was repeated with ka9q-radio source and gnuradio both on a single core i7 computer</div><div>(using the loopback data connection). That system runs without drops for a few minutes</div><div>(which was the limit of the test duration).</div><div><br></div>Franco has tested RPi4 to Linux host with a direct connection without drops. However he is<div>using a different SDR receiver than RTLSDR for that test.</div><div><br></div><div>A separate test was run with a direct hard wired connection from the RPI4 to the Linux host.</div><div>One has to set static IP addresses, and inject static IP routes for the LAN and the multicast</div><div>range <a href="http://224.0.0.0/4" target="_blank">224.0.0.0/4</a> on both ends.   That setup was unusable with about 50% packet loss rate, </div><div>but this was prior to the fft-threads change (above). It has not been rerun since the fft-threads change.</div><div><br></div><div>Some speculations and observations:</div><div><br></div><div>* The different SDR drivers appear to have some significant performance variations.</div><div><br></div><div>* Different switches and links have different iperf3 retry rates, but they don't seem to affect the</div><div>drop rates much.</div><div><br></div><div>* The RPI3 B+seems a bit too slow for 192 ksps, but was marginally OK for 48 ksps.</div><div><br></div><div>* A faster SBC might be beneficial in place of the RPI4. That would be a good test to try.<br></div><div><br></div><div>Again, much thanks to Franco, who has provided software instrumentation to measure the loss rates</div><div>both inside of gnuradio and outside of gnuradio (i.e. with gnuradio not running).</div><div><br></div><div>-- Tom, N5EG</div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div></div>
-- <br>
TangerineSDR mailing list<br>
<a href="mailto:TangerineSDR@lists.tapr.org" target="_blank">TangerineSDR@lists.tapr.org</a><br>
<a href="http://lists.tapr.org/mailman/listinfo/tangerinesdr_lists.tapr.org" rel="noreferrer" target="_blank">http://lists.tapr.org/mailman/listinfo/tangerinesdr_lists.tapr.org</a><br>
</blockquote></div><br clear="all"><div><br></div><span class="gmail_signature_prefix">-- </span><br><div dir="ltr" class="gmail_signature">----<br>Phil Erickson<br><a href="mailto:phil.erickson@gmail.com" target="_blank">phil.erickson@gmail.com</a><br></div>