<div dir="ltr"><div>Hi Jonathan,  this looks like a good addition to the receivers available for TangerineSDR.</div><div>The CS5364 IC has some nice specifications, and the ability to receive an external clock,</div><div> so it looks like a good potential choice.</div><div><br></div><div>I notice that the frequency selectable input range is interesting (I've not seen a similar mode</div><div>selection of operation on other components):</div><div>* 2 khz - 54 khz  or<br></div><div>* 54 kHz - 108 kHz  or<br></div><div>* 108 kHz - 216 kHz <br></div><div><br></div><div>-- Tom, N5EG</div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, Jul 12, 2020 at 10:14 PM Jonathan via TangerineSDR <<a href="mailto:tangerinesdr@lists.tapr.org">tangerinesdr@lists.tapr.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Hello,<br>
<br>
For those who don't know me, I'm Jonathan, KC3EEY, a natural radio VLF<br>
enthusiast. I'm also a senior EE student at the University of Scranton<br>
with Nathaniel, W2NAF. When Nathaniel and I first met, we both<br>
discussed our projects, interests, and work. He talked about the<br>
possibility of adding VLF capability to the PSWS and since then I was<br>
always thinking about how to implement it.<br>
<br>
VLF receivers are often homebrew and consist of an input stage<br>
interfacing an H-field loop or E-field probe to a gain or driver stage<br>
with the end result an audio output. It's convenient that  most of the<br>
VLF band is within the audio range which means no downconversion is<br>
needed and can be recorded directly as audio. Some examples of E-Field<br>
receivers are Steve McGreevy's WR-3 and BBB-4, as well as the NASA<br>
Project INSPIRE VLF3 receiver. Most of these receivers are intended<br>
for portable use but can be used in permanent installations. For the<br>
PSWS, VLF receivers will be used in a permanent installation, like the<br>
HF antenna. The intended setup for this purpose will consist of an<br>
E-field receiver and two H-field receivers with orthogonal loops for<br>
triple axial reception. This allows for distance and bearing<br>
calculations of VLF signals.<br>
<br>
The VLF receivers will be setup in a location with minimal power line<br>
interference so as not to overload the input or gain stage of the<br>
receiver. Rural areas are ideal locations, but sometimes suburban<br>
locations can be suitable. The receivers can be powered by batteries<br>
or through isolating DC-DC converters operating at a high switching<br>
frequency above VLF. The audio output from the receivers must also<br>
have an audio isolation transformer on  the audio output on the<br>
receiver. The audio (and sometimes power) is fed through a feedline of<br>
cat5/6 cable or coax, and on the other end it connects to the<br>
soundcard of a computer for audio capture. An audio isolution<br>
transformer is also needed on the soundcard end as well (and an<br>
isolating DC-DC converter if powered by the feedline). The reason<br>
isolation is required is because power line interference can be<br>
coupled into the receiver, often through earth and chassis grounds<br>
like the chassis of a computer.<br>
<br>
For the Tangerine SDR, I wanted to offer to design a plug in module<br>
for one of the interfaces on the data engine. A soundcard is often an<br>
ideal SDR for VLF, so I had a "soundcard interface" module in mind. I<br>
wanted 192 kHz sampling with 16-bit samples and a high dynamic range,<br>
at least 100 dB. After some research, I decoded to use the CS5364<br>
4-channel audio analog to digital converter. Digital audio output is<br>
accomplished with TDM or I2S which is clocked into the FPGA of the<br>
data engine. From there, the samples are GNSS time-stamped and made<br>
available via a TCP socket over the ethernet port.<br>
<br>
As discussed with Tom and Scotty in the Tangerine SDR Zoom, the GPSDO<br>
will provide the A/D master clock and time-stamping will be done in<br>
the FPGA. The CS5364 has both hardware and software configuration mode<br>
and looks fairly easy to use. I plan on looking into the evaluation<br>
board and starting the design of the input stages. This is a little<br>
new to me, but I have dabbled in digital audio in the past,<br>
specifically with Cirrus Logic audio ICs. I plan on laying out the<br>
board in Kicad. Details on the timestamping, possibility of hardware<br>
or software control, and network availability will come soon.<br>
<br>
Thanks again.<br>
<br>
Jonathan<br>
KC3EEY<br>
<br>
-- <br>
TangerineSDR mailing list<br>
<a href="mailto:TangerineSDR@lists.tapr.org" target="_blank">TangerineSDR@lists.tapr.org</a><br>
<a href="http://lists.tapr.org/mailman/listinfo/tangerinesdr_lists.tapr.org" rel="noreferrer" target="_blank">http://lists.tapr.org/mailman/listinfo/tangerinesdr_lists.tapr.org</a><br>
</blockquote></div>