<div dir="ltr"><div>HI Phil, Attached is the group delay curve for the 40 MHz filter.  It's pretty flat up to about 50 MHz then</div><div>climbs in the 6M band. The 50 MHz filter has a different shape, but is within +/- 3 nsec through</div><div>55 MHz., a lot less delay.   The 50 MHz filter probably doesn't require delay compensation, the 40 MHz does for</div><div>measurements above about 45 MHz.  8 nsec is one ADC clock sample time.<br></div> <br><div></div><div>The much bigger concern is the AM broadcast bandstop filter. That has very non-linear phase from about</div><div> 1.8 MHz downwards. Above 1.8 MHz the delay drops and flattens out. That filter will be much more sensitive</div><div>to component variation, so it will need to be calibrated on a per-filter basis.</div><div><br></div><div>-- Tom, N5EG<br></div><div><div><img src="cid:ii_k3q1edcc0" alt="Screenshot from 2019-12-03 07-45-56.png" width="568" height="418"><br></div></div><div><br></div><br><div><br></div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Dec 3, 2019 at 3:29 AM Phil Erickson <<a href="mailto:phil.erickson@gmail.com">phil.erickson@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div>Hi all,</div><div><br></div><div>  Sorry that I was not able to join the call last night.</div><div><br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div>1. Receiver: 40 MHz LPF filter is preferred by the group. The loss at 6M is a little higher, but likely will need an LNA for 6M use anyway, so that may not matter. The nearby-above-61 MHz loss is better with the 40 MHz filter. Also include jumpers for power and ground bonding and for use by some future low-noise amplifier.</div></blockquote><div><br></div><div> One point not brought up in this sentence:  the phase response of the LPF above its cutoff will not necessarily be linear.  Was that discussed?  It might impact any use at 50 MHz, or at the least would require careful calibration if it were to be used there.</div><div><br></div><div>73</div><div>Phil W1PJE</div><div><br></div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Mon, Dec 2, 2019 at 10:11 PM Tom McDermott via TangerineSDR <<a href="mailto:tangerinesdr@lists.tapr.org" target="_blank">tangerinesdr@lists.tapr.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div dir="ltr"><div><br>Notes from PSWS / TangerineSDR call of 12-02-2019</div><div><br></div><div>1. Receiver: 40 MHz LPF filter is preferred by the group. The loss at 6M is a little higher, but likely will need an LNA for 6M use anyway, so that may not matter. The nearby-above-61 MHz loss is better with the 40 MHz filter. Also include jumpers for power and ground bonding and for use by some future low-noise amplifier.</div><div><br></div><div>2. Dave W. recommends putting pads for a low cost I2C temperature sensor on the magnetometer module just in case the PNI-3000 has temperature sensitivity and needs compensation. Scotty recommends adding a strap to one of the temperature sensor address lines so that sensors on the local and remote ends can be separately addressable.</div><div><br></div><div>3. We currently do not have a logo for the Personal Space Weather Station. Would such be useful? Dave L., Scotty, and Nathaniel will add some material to the <a href="http://tangerinesdr.com" target="_blank">tangerinesdr.com</a> webpage tying the various parts of the project together.</div><div><br></div><div>-- Tom, N5EG</div><div><br></div></div></div>
-- <br>
TangerineSDR mailing list<br>
<a href="mailto:TangerineSDR@lists.tapr.org" target="_blank">TangerineSDR@lists.tapr.org</a><br>
<a href="http://lists.tapr.org/mailman/listinfo/tangerinesdr_lists.tapr.org" rel="noreferrer" target="_blank">http://lists.tapr.org/mailman/listinfo/tangerinesdr_lists.tapr.org</a><br>
</blockquote></div><br clear="all"><br>-- <br><div dir="ltr">----<br>Phil Erickson<br><a href="mailto:phil.erickson@gmail.com" target="_blank">phil.erickson@gmail.com</a><br></div>
</blockquote></div>