<div dir="ltr"><div>Hi Nathaniel,  <br></div><div><br></div><div>The Magnetometer RM3100 User Manual has this note attached to paragraph <a href="http://5.2.1.">5.2.1.</a>:</div><div>----------------------<br></div><div>Note: The Cycle Count Registers establish the maximum data rate of the sensors. For instance,<br>if the cycle count is set to 200 D , then the maximum 3-axis update rate is ~430 Hz. If TMRC is set<br>to 0x92, indicating an update rate of ~600 Hz, the rate established by the cycle count will override<br>the TMRC request, and the actual update rate will be ~430 Hz.</div><div>-----------------------</div><div><br></div><div>For the PSWS application and using the range extenders, we would limit the interface to 100 kb/s in</div><div> order to accommodate 30m of cable. In continuous mode, a measurement reading takes 10 register</div><div>reads, with overhead that's about 90 bits, lets round up to 100 bits. That is 1 millisecond to take</div><div>a measurement.   Thus the Magnetometer IC itself is the rate limit for a cycle count of 200, and</div><div>the update rate would be 430 / second.<br></div><div><br></div><div><br></div><div>-- Tom, N5EG</div><div><br></div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Thu, Jul 25, 2019 at 9:48 AM Nathaniel Frissell <<a href="mailto:nafrissell@gmail.com">nafrissell@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr">Hi Tom,<div><br></div><div>This magnetometer document looks fine to me, and I think it will work well for our application. I see the that the resolution of this sensor depends on cycle counts, with 200 cycles for 13 nT. It also says the circuit operates at 180 kHz... so, am I correct in saying that could potential make 900 measurements/second?</div><div><br></div><div>73 de Nathaniel W2NAF</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Jul 24, 2019 at 3:54 PM Tom McDermott via TangerineSDR <<a href="mailto:tangerinesdr@lists.tapr.org" target="_blank">tangerinesdr@lists.tapr.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div>The magnetometer spec has been updated as a result of the 7/22/2019 TeamSpeak session.</div><div><br></div><div>1. Power supply is +5V only. I2C logic levels remain 3.3V.</div><div>2. Add new use case for direct connection to local host not involving Data Engine.</div><div><br></div><div>Attached PDF.</div><div><br></div><div>-- Tom, N5EG</div><div><br></div><div><br></div></div>
-- <br>
TangerineSDR mailing list<br>
<a href="mailto:TangerineSDR@lists.tapr.org" target="_blank">TangerineSDR@lists.tapr.org</a><br>
<a href="http://lists.tapr.org/mailman/listinfo/tangerinesdr_lists.tapr.org" rel="noreferrer" target="_blank">http://lists.tapr.org/mailman/listinfo/tangerinesdr_lists.tapr.org</a><br>
</blockquote></div>
</blockquote></div>