A few other bits of info:<br><br>On the jnos side, the log now contains the messages<br><br><span style="font-family:courier new,monospace">21:59:00  - using new [tun0] device</span><br style="font-family:courier new,monospace">
<span style="font-family:courier new,monospace">21:59:00  - tun_rx - listening for packets</span><br style="font-family:courier new,monospace"><br>where the "unable to setup tunnel" had been.<br><br>An additional command that's in my autoexec.nos, but that I failed to document in my last post, is:<br>
<br><span style="font-family:courier new,monospace">start telnet</span><br><br>This is after all the other commands that I did document (actually, all the way at the end of my autoexec.nos file -- which is why I missed it last time).<br>
<br>On the jnos side, "ifconfig tun0" shows packets sent and received -- in fact, one more in each direction than the number of telnet attempts made from the linux side. For example, this is the output after three telnet attempts.<br>
<br><span style="font-family:courier new,monospace">tun0     IP addr 192.168.1.67 MTU 1500 Link encap TUN</span><br style="font-family:courier new,monospace"><span style="font-family:courier new,monospace">         flags 0x0 trace 0x0 netmask 0x00000255 broadcast 0.0.0.0</span><br style="font-family:courier new,monospace">
<span style="font-family:courier new,monospace">         sent: ip 4 tot 4 idle 0:00:00:17</span><br style="font-family:courier new,monospace"><span style="font-family:courier new,monospace">         recv: ip 4 tot 4 idle 0:00:00:17</span><br>
<br>On the linux side, each attempt to telnet to the IP address of the jnos end of the tunnel increments both the "TX bytes" and "RX bytes" reported by ifconfig for the tun0 interface (by 60 and 40, respectively). This is the output of "ifconfig tun0" after three telnet attempts:<br>
<br><span style="font-family:courier new,monospace">tun0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  </span><br style="font-family:courier new,monospace"><span style="font-family:courier new,monospace">          inet addr:192.168.1.68  P-t-P:192.168.1.67  Mask:255.255.255.255</span><br style="font-family:courier new,monospace">
<span style="font-family:courier new,monospace">          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1500  Metric:1</span><br style="font-family:courier new,monospace"><span style="font-family:courier new,monospace">          RX packets:4 errors:0 dropped:0 overruns:0 frame:0</span><br style="font-family:courier new,monospace">
<span style="font-family:courier new,monospace">          TX packets:4 errors:0 dropped:0 overruns:0 carrier:0</span><br style="font-family:courier new,monospace"><span style="font-family:courier new,monospace">          collisions:0 txqueuelen:500 </span><br style="font-family:courier new,monospace">
<span style="font-family:courier new,monospace">          RX bytes:160 (160.0 B)  TX bytes:240 (240.0 B)</span><br><br>So both sides seem to agree that packets are flowing between them, but apparently not the right ones to result in a proper telnet connection.<br>
<br>Any ideas what to try next? Thanks for all the feedback so far!<br><br>M<br>-- <br>This cat is pushing a watermelon out of a lake. Your argument is invalid.<br><br>