[nos-bbs] Telnet etc.

[Boudewijn (Bob) Tenty]

The DMZ should normally pointed to your PI address (10.0.0.196). I have to say that I do the IPIP tunnels in Linux and I
don't know or you do IPIP/encap in Linux (PI) or in jnos?

Bob VE3TOK

On 2023-10-12 18:06, Don Moore wrote:
> I checked the file and yes it is as you’ve written, no # at the beginning of the line to ensure forwarding is turned on.
> Do you think if I changed the ip addresses for tun0 were changed to
> 10.0.0.197 and 10.0.0.198 that it would make a difference or maybe DMZ the pi instead of tun0?
> Regards,
> Don
>
>
> On Thu, Oct 12, 2023 at 3:28 PM Boudewijn (Bob) Tenty <bob at tenty.ca> wrote:
>
>     I don't believe is your cable modem and as you said there is no other firmware available for it. I believe VE3CLG has the
>     same modem and he has no problem with it.  Do you have net.ipv4.ip_forward=1  enabled in /etc/sysctl.conf of your PI?
>
>     73,
>
>     Bob VE3TOK
>
>     On 2023-10-12 14:35, Don Moore wrote:
>>     I was thinking that I am DMZ the jnos side of tun0….150. Is it or could it be something as simple as DMZ the pi side….149
>>
>>
>>
>>     On Thu, Oct 12, 2023 at 2:17 PM Don Moore <ve3zda at gmail.com> wrote:
>>
>>         Hey Bob
>>         It’s a rogers ignite modem and I don’t think they offer different firmware for it. I use wired from the modem to jnos.
>>         This may or may not have something to do with it.
>>         The pi address is 10.0.0.196 and tun0 has ….149 to …150
>>         The modem allows DMZ to tun0 ….150 but tcp forward is  to ….196.
>>         There is no option to forward directly to …..150
>>         If that’s the case is there a command in the the pi that’s required to enable port forwarding to/from tun0
>>
>>         73
>>         Don - ve3zda
>>
>>
>>         On Thu, Oct 12, 2023 at 2:02 PM Boudewijn (Bob) Tenty <bob at tenty.ca> wrote:
>>
>>             Don,
>>
>>             It could be your consumer router. Those links from you keep the incoming route open for those  ip numbers
>>             for some time, that could be 5 or maybe 15 minutes or so and in that time there is other traffic from your station
>>             that resets those timers and keep it open, etc. The best way to solve that is replacing the firmware with WRT if  that
>>             is available for the chip-set in that router and if it is your own and there is no setting to override that.  I see that you
>>             have a cable connection, but I don't know or that cable modem is the only consumer router you have in line?
>>
>>             73,
>>
>>             Bob VE3TOK
>>
>>
>>             On 2023-10-12 13:06, Don Moore wrote:
>>>             I’m wondering if someone can tell me what might be wrong.
>>>             Telnet works perfectly to me via any of my links but not from anyone else however I can telnet to anyone.
>>>             My station is set up using DMZ so all traffic is getting to jnos tun0
>>>
>>>             Regards,
>>>             Don - ve3zda
>>>
>>>             _______________________________________________
>>>             nos-bbs mailing list
>>>             nos-bbs at lists.tapr.org
>>>             http://lists.tapr.org/mailman/listinfo/nos-bbs_lists.tapr.org
>>
>>             -- 
>>             There is nothing permanent except change
>>               
>>             -Heraclitus
>>
>     -- 
>     There is nothing permanent except change
>       
>     -Heraclitus
>
>     _______________________________________________
>     nos-bbs mailing list
>     nos-bbs at lists.tapr.org
>     http://lists.tapr.org/mailman/listinfo/nos-bbs_lists.tapr.org
>
>
> _______________________________________________
> nos-bbs mailing list
> nos-bbs at lists.tapr.org
> http://lists.tapr.org/mailman/listinfo/nos-bbs_lists.tapr.org

-- 
There is nothing permanent except change
  
-Heraclitus
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.tapr.org/pipermail/nos-bbs_lists.tapr.org/attachments/20231012/7a32931e/attachment.html>