[nos-bbs] Puppy Linux & Jnos2h - Success!

[jerome schatten]

That was it all right. For what it's worth in Puppy Linux:
echo 1 > /proc/sys/net/ipv4/conf/all/forward
does the trick.
Thanks much,
jerome -VA7VV


On Tue, 2011-02-08 at 18:58 -0800, jerome schatten wrote:
> Thanks Bob... I'll try and see what the situation is with ipv4
> forwarding. I should have thought of that myself as I got trapped with
> that under ubuntu initially. With puppy, the usual problem is to find
> out where things are. I'll report back.
> 73
> jerome va7vv
> 
> On Tue, 2011-02-08 at 20:15 -0500, Bob Tenty wrote:
> > Is packet forwarding enabled for IPV4 ?
> > 
> > in /etc/sysctl.conf (ubtuntu, don't know what puppy is using) it was
> > 
> > net.ipv4.ip_forward=1
> > 
> > By default it is hashed out, if you remove the hash,
> > 
> > run:  sysctl -a      to make it active.
> > 
> > or alternate check the setting with: cat /proc/sys/net/ipv4/ip_forward
> > 
> > if "0"  set to "1" with:
> > 
> > echo 1 >> /proc/sys/net/ipv4/ip_forward
> > 
> > and add it to rc.local
> > 
> > 73,
> > 
> > Bob VE3TOK
> > 
> > On 11-02-08 12:19 PM, jerome schatten wrote:
> > > I'm trying to get jnos2h and puppy 4.0 to work together with an eye to
> > > running with no hard drive.
> > >
> > > I'm using the same binary and the same configuration files that I've
> > > used with ubuntu on the same machine. Jnos runs flawlessly under ubuntu
> > > in all respects. I figured it would probably work ok with puppy, since
> > > I'm using the same physical computer.
> > >
> > > Under puppy, The RF port works fine but the internet connectivity does
> > > not. Tun0 is running; I can see that with 'ifconfig'.
> > >
> > > I can ping both sides of the tun0 interface from within jnos, and I can
> > > ping the computer's ip as well. I cannot, however ping my router at all.
> > > so nothing gets out internet wise.
> > >
> > > > From outside jnos, everyting works in puppy... full internet
> > > connectivity, browser,etc,  and I can ping both sides of the tun0
> > > interface from a puppy terminal outside of jnos. I can also telnet into
> > > jnos from another puppy terminal on the same machine. The setup on the
> > > router was not changed.
> > >
> > > The default routing for puppy is exactly as it was for ubuntu so the
> > > default route for tun0 is to the router.
> > >
> > > Any ideas about what to look at/for now?
> > >
> > > 73
> > > jerome VA7VV
> > >
> > >
> > >
> > > _______________________________________________
> > > nos-bbs mailing list
> > > nos-bbs at tapr.org
> > > https://www.tapr.org/cgi-bin/mailman/listinfo/nos-bbs
> > 
> > 
> > _______________________________________________
> > nos-bbs mailing list
> > nos-bbs at tapr.org
> > https://www.tapr.org/cgi-bin/mailman/listinfo/nos-bbs
> 
> 
> 
> _______________________________________________
> nos-bbs mailing list
> nos-bbs at tapr.org
> https://www.tapr.org/cgi-bin/mailman/listinfo/nos-bbs