<div dir="ltr">Hi Mike,<div><br></div><div>Which RPi version and which distribution you use on the SD card?</div><div><br></div><div>The easiest debug is to use a micro USB current meter, the RPi's consumption difference from idle to transmit should be about 50 mA.</div><div><br></div><div>If you going to listen to the transmitted signal then need to tune your radio to <span style="color:rgb(0,0,0);font-family:Arial,Verdana,sans-serif;font-size:13.12px;line-height:17.056px;background-color:rgb(238,244,249)">14.0956 MHz in USB SSB mode.</span></div><div><span style="color:rgb(0,0,0);font-family:Arial,Verdana,sans-serif;font-size:13.12px;line-height:17.056px;background-color:rgb(238,244,249)">Your RPi also needs internet connection to make the frequency calibration.</span></div><div><span style="color:rgb(0,0,0);font-family:Arial,Verdana,sans-serif;font-size:13.12px;line-height:17.056px;background-color:rgb(238,244,249)"><br></span></div><div><span style="color:rgb(0,0,0);font-family:Arial,Verdana,sans-serif;font-size:13.12px;line-height:17.056px;background-color:rgb(238,244,249)">You will need this manual: </span><font color="#000000" face="Arial, Verdana, sans-serif"><span style="font-size:13.12px;line-height:17.056px"><a href="http://j.mp/tapr-qrpi">http://j.mp/tapr-qrpi</a></span></font></div><div><font color="#000000" face="Arial, Verdana, sans-serif"><span style="font-size:13.12px;line-height:17.056px"><br></span></font></div><div><font color="#000000" face="Arial, Verdana, sans-serif"><span style="font-size:13.12px;line-height:17.056px">73,</span></font></div><div><font color="#000000" face="Arial, Verdana, sans-serif"><span style="font-size:13.12px;line-height:17.056px">HA7DCD<br>Zoltan</span></font></div><div><br></div><div><br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Jul 11, 2016 at 3:53 AM, Mike Myers <span dir="ltr"><<a href="mailto:netnutmike@gmail.com" target="_blank">netnutmike@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr">When I transmit I do not hear anything.  I even moved around some on the band just to make sure.  Does anyone know of a debugging process for these boards?</div><div class="gmail_extra"><br><div class="gmail_quote">On Sat, Jul 9, 2016 at 1:00 PM,  <span dir="ltr"><<a href="mailto:hfsig-request@tapr.org" target="_blank">hfsig-request@tapr.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Send hfsig mailing list submissions to<br>
        <a href="mailto:hfsig@tapr.org" target="_blank">hfsig@tapr.org</a><br>
<br>
To subscribe or unsubscribe via the World Wide Web, visit<br>
        <a href="http://www.tapr.org/mailman/listinfo/hfsig" rel="noreferrer" target="_blank">http://www.tapr.org/mailman/listinfo/hfsig</a><br>
or, via email, send a message with subject or body 'help' to<br>
        <a href="mailto:hfsig-request@tapr.org" target="_blank">hfsig-request@tapr.org</a><br>
<br>
You can reach the person managing the list at<br>
        <a href="mailto:hfsig-owner@tapr.org" target="_blank">hfsig-owner@tapr.org</a><br>
<br>
When replying, please edit your Subject line so it is more specific<br>
than "Re: Contents of hfsig digest..."<br>
<br>
<br>
Today's Topics:<br>
<br>
   1. 20M WSPR Raspi Board issue (Mike Myers)<br>
   2. Re: 20M WSPR Raspi Board issue (N7QNM)<br>
   3. Re: 20M WSPR Raspi Board issue (Yahoo)<br>
<br>
<br>
----------------------------------------------------------------------<br>
<br>
Message: 1<br>
Date: Fri, 8 Jul 2016 14:26:50 -0400<br>
From: Mike Myers <<a href="mailto:netnutmike@gmail.com" target="_blank">netnutmike@gmail.com</a>><br>
To: <a href="mailto:hfsig@tapr.org" target="_blank">hfsig@tapr.org</a><br>
Subject: [hfsig] 20M WSPR Raspi Board issue<br>
Message-ID:<br>
        <<a href="mailto:CAGeDYM27zQ8xM12yE8q2D6%2BwroMf%2BSqDHDqTOoohG0eios36xA@mail.gmail.com" target="_blank">CAGeDYM27zQ8xM12yE8q2D6+wroMf+SqDHDqTOoohG0eios36xA@mail.gmail.com</a>><br>
Content-Type: text/plain; charset="utf-8"<br>
<br>
Good afternoon everyone,<br>
<br>
   I recently purchased the Raspi 20M WSPR board and over the past weekend<br>
put it on a raspi.  I followed the instructions on the tapr website for<br>
installation and put on Wsprrypi following the guide.  When I run the<br>
command line in the document, it says it is transmitting but listening on<br>
the frequency I hear nothing.  I tried putting a power meter in 5 watt mode<br>
to see if the needle would even move and no luck.<br>
<br>
I am not quite sure how to debug and wondering if anyone can point me in<br>
the correct directions.<br>
<br>
Thank you!<br>
<br>
--<br>
<br>
<br>
Mike Myers<br>
<a href="mailto:netnutmike@gmail.com" target="_blank">netnutmike@gmail.com</a><br>
K3DO<br>
<br>
<a href="http://mikemyers.me" rel="noreferrer" target="_blank">http://mikemyers.me</a><br>
-------------- next part --------------<br>
An HTML attachment was scrubbed...<br>
URL: <<a href="http://www.tapr.org/pipermail/hfsig/attachments/20160708/c3052a4f/attachment-0001.html" rel="noreferrer" target="_blank">http://www.tapr.org/pipermail/hfsig/attachments/20160708/c3052a4f/attachment-0001.html</a>><br>
<br>
------------------------------<br>
<br>
Message: 2<br>
Date: Fri, 8 Jul 2016 12:59:42 -0700<br>
From: "N7QNM" <<a href="mailto:n7qnm-lists@nwlink.com" target="_blank">n7qnm-lists@nwlink.com</a>><br>
To: "'TAPR HF Modes SIG Mailing List'" <<a href="mailto:hfsig@tapr.org" target="_blank">hfsig@tapr.org</a>><br>
Subject: Re: [hfsig] 20M WSPR Raspi Board issue<br>
Message-ID: <07f401d1d953$47a76240$d6f626c0$@<a href="http://nwlink.com" rel="noreferrer" target="_blank">nwlink.com</a>><br>
Content-Type: text/plain; charset="utf-8"<br>
<br>
Hi, Mike – I’m having a similar issue – when I transmit; I see broadband noise (freq +/-  5Khz) and hear no tones, buts a really raspy buzz.  At first, I thought it was a power supply (POE), so I tried using a 12V battery supply with an in-line regulator,  still the same.   I’m guessing that I’m hearing the “raw” GPIO output; but wondering why.<br>
<br>
<br>
<br>
Thanks in advance!<br>
<br>
<br>
<br>
Clay<br>
<br>
N7QNM<br>
<br>
<br>
<br>
<br>
<br>
From: hfsig [mailto:<a href="mailto:hfsig-bounces@tapr.org" target="_blank">hfsig-bounces@tapr.org</a>] On Behalf Of Mike Myers<br>
Sent: Friday, July 8, 2016 11:27 AM<br>
To: <a href="mailto:hfsig@tapr.org" target="_blank">hfsig@tapr.org</a><br>
Subject: [hfsig] 20M WSPR Raspi Board issue<br>
<br>
<br>
<br>
Good afternoon everyone,<br>
<br>
<br>
<br>
   I recently purchased the Raspi 20M WSPR board and over the past weekend put it on a raspi.  I followed the instructions on the tapr website for installation and put on Wsprrypi following the guide.  When I run the command line in the document, it says it is transmitting but listening on the frequency I hear nothing.  I tried putting a power meter in 5 watt mode to see if the needle would even move and no luck.<br>
<br>
<br>
<br>
I am not quite sure how to debug and wondering if anyone can point me in the correct directions.<br>
<br>
<br>
<br>
Thank you!<br>
<br>
<br>
<br>
<br>
--<br>
<br>
<br>
<br>
<br>
<br>
Mike Myers<br>
<br>
<a href="mailto:netnutmike@gmail.com" target="_blank">netnutmike@gmail.com</a> <mailto:<a href="mailto:netnutmike@gmail.com" target="_blank">netnutmike@gmail.com</a>><br>
<br>
K3DO<br>
<br>
<br>
<br>
<a href="http://mikemyers.me" rel="noreferrer" target="_blank">http://mikemyers.me</a><br>
<br>
-------------- next part --------------<br>
An HTML attachment was scrubbed...<br>
URL: <<a href="http://www.tapr.org/pipermail/hfsig/attachments/20160708/281c0e64/attachment-0001.html" rel="noreferrer" target="_blank">http://www.tapr.org/pipermail/hfsig/attachments/20160708/281c0e64/attachment-0001.html</a>><br>
<br>
------------------------------<br>
<br>
Message: 3<br>
Date: Fri, 8 Jul 2016 16:48:19 -0400<br>
From: Yahoo <<a href="mailto:ftr300@yahoo.com" target="_blank">ftr300@yahoo.com</a>><br>
To: TAPR HF Modes SIG Mailing List <<a href="mailto:hfsig@tapr.org" target="_blank">hfsig@tapr.org</a>><br>
Subject: Re: [hfsig] 20M WSPR Raspi Board issue<br>
Message-ID: <<a href="mailto:EFDEBEAE-1B77-40F7-A35C-A7E9471EAE91@yahoo.com" target="_blank">EFDEBEAE-1B77-40F7-A35C-A7E9471EAE91@yahoo.com</a>><br>
Content-Type: text/plain; charset="utf-8"<br>
<br>
I will add my two cents in... My board worked fine and is now live on 20.<br>
Did you tune around 14.071 freq a couple of kc's to see if you hear a tone but off a bit?<br>
Tom ka8huz<br>
<br>
Sent from my iPad<br>
<br>
> On Jul 8, 2016, at 3:59 PM, N7QNM <<a href="mailto:n7qnm-lists@nwlink.com" target="_blank">n7qnm-lists@nwlink.com</a>> wrote:<br>
><br>
> Hi, Mike – I’m having a similar issue – when I transmit; I see broadband noise (freq +/-  5Khz) and hear no tones, buts a really raspy buzz.  At first, I thought it was a power supply (POE), so I tried using a 12V battery supply with an in-line regulator,  still the same.   I’m guessing that I’m hearing the “raw” GPIO output; but wondering why.<br>
><br>
> Thanks in advance!<br>
><br>
> Clay<br>
> N7QNM<br>
><br>
><br>
> From: hfsig [mailto:<a href="mailto:hfsig-bounces@tapr.org" target="_blank">hfsig-bounces@tapr.org</a>] On Behalf Of Mike Myers<br>
> Sent: Friday, July 8, 2016 11:27 AM<br>
> To: <a href="mailto:hfsig@tapr.org" target="_blank">hfsig@tapr.org</a><br>
> Subject: [hfsig] 20M WSPR Raspi Board issue<br>
><br>
> Good afternoon everyone,<br>
><br>
>    I recently purchased the Raspi 20M WSPR board and over the past weekend put it on a raspi.  I followed the instructions on the tapr website for installation and put on Wsprrypi following the guide.  When I run the command line in the document, it says it is transmitting but listening on the frequency I hear nothing.  I tried putting a power meter in 5 watt mode to see if the needle would even move and no luck.<br>
><br>
> I am not quite sure how to debug and wondering if anyone can point me in the correct directions.<br>
><br>
> Thank you!<br>
><br>
> --<br>
><br>
><br>
> Mike Myers<br>
> <a href="mailto:netnutmike@gmail.com" target="_blank">netnutmike@gmail.com</a><br>
> K3DO<br>
><br>
> <a href="http://mikemyers.me" rel="noreferrer" target="_blank">http://mikemyers.me</a><br>
> _______________________________________________<br>
> hfsig mailing list<br>
> <a href="mailto:hfsig@tapr.org" target="_blank">hfsig@tapr.org</a><br>
> <a href="http://www.tapr.org/mailman/listinfo/hfsig" rel="noreferrer" target="_blank">http://www.tapr.org/mailman/listinfo/hfsig</a><br>
-------------- next part --------------<br>
An HTML attachment was scrubbed...<br>
URL: <<a href="http://www.tapr.org/pipermail/hfsig/attachments/20160708/37c9bcf8/attachment-0001.html" rel="noreferrer" target="_blank">http://www.tapr.org/pipermail/hfsig/attachments/20160708/37c9bcf8/attachment-0001.html</a>><br>
<br>
------------------------------<br>
<br>
Subject: Digest Footer<br>
<br>
_______________________________________________<br>
hfsig mailing list<br>
<a href="mailto:hfsig@tapr.org" target="_blank">hfsig@tapr.org</a><br>
<a href="http://www.tapr.org/mailman/listinfo/hfsig" rel="noreferrer" target="_blank">http://www.tapr.org/mailman/listinfo/hfsig</a><br>
<br>
<br>
------------------------------<br>
<br>
End of hfsig Digest, Vol 26, Issue 1<br>
************************************<span class="HOEnZb"><font color="#888888"><br>
</font></span></blockquote></div><span class="HOEnZb"><font color="#888888"><br><br clear="all"><div><br></div>-- <br><div data-smartmail="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div><div dir="ltr"><div><div dir="ltr"><br><div><br></div><div>Mike Myers</div><div><a href="mailto:netnutmike@gmail.com" target="_blank">netnutmike@gmail.com</a></div><div>K3DO</div><div><br></div><div><a href="http://mikemyers.me" target="_blank">http://mikemyers.me</a></div></div></div></div></div></div></div></div></div>
</font></span></div>
<br>_______________________________________________<br>
hfsig mailing list<br>
<a href="mailto:hfsig@tapr.org">hfsig@tapr.org</a><br>
<a href="http://www.tapr.org/mailman/listinfo/hfsig" rel="noreferrer" target="_blank">http://www.tapr.org/mailman/listinfo/hfsig</a><br>
<br></blockquote></div><br></div>